Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
In this article in the next paragraph yow will discover a good deal of good content around A Step-by-Step Guide to Installing a Bathtub.
Mounting a bathtub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a moderately tough project. If the old bathtub is conveniently accessible, the project can move rapidly; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Ensure you have qualified yourself for the task and also fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to consider using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you set up a new tub in your restroom if you have already bought a new tub and do not require to alter the plan of your previous supply of water pipes.
Your tools and product list ought to comprise the following:
Getting ready for the Setup
Firstly, the supporting structure provided with the bathroom ought to be fitted (if required) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its final position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite bothersome due to the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, place the tub in the needed setting. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the bath tub up until the level reviews degree.
To install taps, fit the bottom of the furthest flexible faucet port to the proper supply pipeline by making a compression join; after that do the very same for the various other faucet.
Activate the water supply and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Finally, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub must wait until the bathtub has been made use of at the very least when as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type must be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a stiff seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to enable the motion experienced when the tub is in usage. The sealant can split rather early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about How to Install a Bathtub? Put a remark down below. We will be pleased to hear your thoughts about this posting. In hopes that you come back again before long. Be sure to take a moment to promote this content if you enjoyed reading it. Kudos for your time. Please stop by our website back soon.
Book Now!
Report this page